Showing results: 2626 - 2640 of 3393 items found.
-
LS-68-M -
Lumistar Inc.
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
TimeSpy -
Brandywine Communications
The TimeSpy precisely measures the time accuracy of a wide range of inputs (such as: NTP, IRIG B, 1PPS, and ASCII) against an internal precision GPS-controlled oscillator, displayed on the large, full color windows-based touch screen. The TimeSpy can precisely measure the time error at the point of use for systems where time is distributed over large distances. The TimeSpy can also measure free-running clocks and timing systems which are synchronized from untraceable sources, such as television and radio broadcasts, electrical power lines and the internet.
-
PCAAD 7.0 -
Antenna Design Associates, Inc.
PCAAD 7.0 is a Windowscompatible antenna analysis, modeling, and design software package. It contains more than 50 routines treating wire antennas, aperture antennas, microstrip antennas, arrays, transmission lines and waveguides, and more. These routines are integrated into a menudriven, userfriendly system allowing you to quickly evaluate the performance of a wide variety of antenna types. PCAAD 7.0 includes a 120-page printed user manual which describes the use of the software, provides examples for each of the routines, and lists technical references.
-
CD280 -
Validyne Engineering
The CD280 Carrier Demodulator is a complete multi channel system in a small package which houses a plug-in power supply and 4 carrier demodulator circuit boards. The power supply provides regulated 5 Vac 5 kHz carrier power for Variable Reluctance and LVDT transducers , and the carrier demodulators demodulate and amplify the input signals to a 10 Vdc full-scale output. Zero and span adjustments are available for each channel. The system operates from 115 Vac, 50 to 400 Hz, line power.
-
DP15TL -
Validyne Engineering
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
8PK-ST850 -
Prokit's Industries Co., Ltd.
Two functions in one unit incluidng open phase and phase sequence. Large size alligator clips : able to clip on switch-board terminals easily. Identify 3 phase sequence and open phase check Ideal for installing conveyor lines, pump systems and interconnected drivers. No exposed metal parts. Safety features are incorporated throughout, including the pushbutton switch designed to minimize damage due to negligence. Safety approval: CE marks, IEN 1010 CAT. II.
-
ARTES -
KoCoS Messtechnik AG
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
Bloomy Controls, Inc.
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
MHTXE -
Elmika
The MHTXE Magic Tee Hybrid Couplers for millimeter waves are matched power dividers for variety of applications (general purpose power splitters, power combiners, phase measurement circuits, phase / frequency discriminators). The MHTXE Magic Tee Hybrid Couplers are available in waveguide bands between 33 and 170 GHz. These couplers are four-port transmission line components with a port configuration as shown in figure. Operation bandwidth is limited to 20÷90% waveguide operation frequency range depending on performance specifications.
-
Hilkar
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
Extech 480826 -
Extech Instruments Corporation
480826 Triple Axis EMF Tester is designed to provide a quick, reliable and easy way to measure electromagnetic field radiation levels around power lines, electrical appliances and industrial devices. Provides Three axis (X, Y, Z direction) electromagnetic field measurement. Calibrated to measure EMF radiation at wide bandwidths from 30 Hz to 300 Hz. Complete with sensor with 3 ft. (930 mm) cable, 9V battery, and hard carrying case.
-
ENX112 -
ESPEC North America, INC.
The ENX112 chambers provide a test chamber large enough for testing full-size PV modules in the least amount of floorspace. Can be use for panels 1.2m x 2m or larger.These models provide a variety of performance capabilities to meet maximum or minimum change rates in IEC or UL test standards. Incorporated are the features of our smaller Platinum and Global-N lines. The refrigeration systems of these models utilize modern, high performance scroll compressors that allow a small footprint while allowing unparalleled service access.
-
TLP -
Impulse Semiconductor Inc.
The Impulse transmission line pulser (TLP) discharge networks are easily integrated with other instruments for a custom system matched for your device and process applications. Specifications include 1-10 nanosecond rise times, up to 40 amps peak, for 10-500 nanosecond pulse widths. It is a proven design incorporating 15 years of hardware and device development experience. Reliable performance over hundreds of processes, and thousands of products. All TLP systems are built by special request, contact us with your specifications or application.
-
MC1400 -
Manncorp
MC1400 Automatic stencil printer MC1400's automatic dual-vision alignment system ensures accuracy while the printer's linear-guided movements and vertical stencil separation provide high precision and repeatability, a combination that results in ultra-fine-pitch printing capability for component pitches down to 0.3 mm (12 mil). With quick setup and changeover, thanks to the flexible mounting table, MC1400 stencil printer easily keeps pace with medium to high volume production lines and is well-suited to precision batch printing.
-
Fairview Microwave Inc.
Fairview Microwave’s line of electromechanical relay transfer switches can be utilized for numerous applications to increase system level capabilities and can help simplify the overall design approach. With two input and two output ports, transfer switches can connect two different instruments with two devices under test. Additionally, they can be used as drop-out switches, for signal reversal or to bypass a component under test. These products are typically used in military communications and broadcast systems, SATCOM, test & measurement, instrumentation applications and are suitable for aircraft use.
